Selectează o Pagină

Sa de bransament Electrosudabila

SAFL

Sa de bransament Electrosudabila cu iesire prin flansa

Spigot Saddles with flange outlet
Compact fitting in HD-PE. Manufactured combination of FRIALEN spigot saddle, coupler and FRIALEN Full Faced Flanges EFL (compact flange). Saddle with exposed heating coil for optimum heat transfer. Tapping in pressure free condition or, using an additional shut-off valve, under operating pressure by means of standard tapping equipment (we recommend Hütz & Baumgarten (www.huetz-baumgarten.de)). We recommend steel-reinforced elastomeric gaskets.

Additional washers are necessary for the flange reducer.

For tapping under pressure, please contact our hotline: +49 621 486-2325.

PE 100 SDR 11

Maximum working pressure 16 bar (water)

SKU d1 DN BX PU D L B dk Z Ø k H Holes b Drilling
Ø da		 Weight kg
616016 110/80 3 54 204 190 165 16,50 180 160 296 8 25 65 3,700
616017 125/80 2 36 204 205 185 16,50 180 160 311 8 25 65 3,940
616018 160/80 2 36 204 245 217 16,50 180 160 346 8 25 65 4,320
616019 180/80 2 36 204 285 241 16,50 180 160 366 8 25 65 4,610
616020 225/80 2 16 204 284 286 16,50 180 160 411 8 25 65 4,720
616022 160/100 2 36 224 245 217 16,50 180 180 346 8 27 84 5,270
616024 225/100 2 16 224 284 286 16,50 180 180 411 8 27 84 5,635

FRIALEN-Safety Fittings can be fused to pipes of SDR stages 11 to 17.6. Other SDR-stages on request. Please observe the marking directly at the product, which is mandatory. DVGW-Registration No.: DV-8606AU2249

Areas of Application

The FRIALEN Spigot Saddle with Flange Outlet SAFL is used for the integration of flange valves and hydrants up to PN 16.

Assembly Instructions

The saddle of the SAFL is mounted and fused onto the HD-PE mains. Drilling into the HD-PE mains can take place

  • without pressure in the mains
  • under operating pressure on application of a gate-valve on the flange side

using standard drill equipment. We recommend Hütz + Baumgarten.

The fusion of the saddle piece with the HD-PE mains takes place using FRIALEN-fusion –leakproof and longitudinally strong. Saddle and HD-PE mains are prepared according to the general installation instructions (see Assembly Instructions for “FRIALEN-Safety Fittings for house connections and distribution pipes up to d 225”). This involves removing oxide skin.

The flange connection measurements correspond to DIN EN 1092-1. Supplementary washers are required.

All standard profile and flat gaskets can be used. Torques advised by the gasket manufacturer must be observed. We recommend profile gaskets of type G-St.

Good reasons for using the FRIALEN-Spigot Saddle with Flange Outlet SAFL:

  • Compact component from HD-PE
  • Flange adaptor and flange are one component. They make up one homogeneous unit
  • Factory made combination of FRIALEN-Spigot Saddle, FRIALEN-Coupler and Full Faced Flange
  • Smooth on the inside and no fusion bead at the connection between SA and EFL, optimum hydraulics
  • The cold flowing properties well known with HD-PE are avoided by constructive flange design
  • Solid construction. Integration of the flange prevents tear-off
  • Short overall length for horizontal and vertical installation
  • Top stability due to great wall thickness
  • Extremely economical solution
  • Additional barcode for tracing back the underground fitting (Traceability-Coding)