Selectează o Pagină

Teu egal Electrosudabile

TA RED

Teu redus Electrosudabil cu stut extralung

T-Pieces with reduced outlet spigot
With exposed heating coils for optimal heat transfer, large insertion depth, wide fusion zones plus cold zones at the end and in the middle to prevent the flow of molten material, for use without holding devices. Separate fusion zones. Outlet spigot SDR 11 for proccessing couplers UB/MB.

with extra long outlet spigot

with extra long outlet spigot

SKU d1 d2 BX PU D L L1 t t1 z h B Weight kg
616417 32 20 30 540 46 116 117 44 42 14 22 62 0,110
616418 40 32 20 360 55 146 148 46 51 28 25 70 0,170
616419 50 32 10 180 69 175 158 55 51 33 28 82 0,295
616420 50 40 10 180 69 175 167 55 55 33 28 82 0,315
616421 63 32 10 180 84 197 173 63 51 36 32 96 0,435
616422 63 40 10 180 84 197 182 63 55 36 32 96 0,450
616423 63 50 10 180 84 197 197 63 60 36 32 96 0,490

FRIALEN safety fittings can be fused to pipes SDR11 – SDR 17.6. Minimum wall thickness s min ≥ 3 mm. Other SDR-stages on request. Please observe the marking directly at the product, which is mandatory. DVGW-Registration No.: DV-8601AU2248 and DV-8606AU2249.

with normal sized spigot

with normal sized spigot

SKU d1 d2 BX PU D L L1 t t1 z h B Weight kg
616675 90 32 17 136 116 280 172 79 44 61 43 126 1,050
616676 90 63 15 120 116 280 191 79 63 61 43 126 1,100
616678 110 63 8 64 141 310 216 82 63 73 48 148 1,700
616679 110 90 8 64 141 310 244 82 79 73 48 148 1,850
616681 160 90 4 32 203 390 305 98 79 97 45 205 4,400
616682 160 110 4 32 203 390 308 98 82 97 45 205 4,500
616683 160 125 3 24 203 390 313 98 87 97 45 205 4,600
616427 250 225 1 2 310 770 440 128 – 254 80 – 23,500
616429 280 225 1 2 350 905 475 139 – 312 84 – 35,500
616431 315 225 1 2 396 940 525 150 – 359 80 – 43,500

FRIALEN safety fittings can be fused to pipes SDR11 – SDR 17.6. Minimum wall thickness s min ≥ 3 mm. Other SDR-stages on request. Please observe the marking directly at the product, which is mandatory. DVGW-Registration No.: DV-8601AU2248 and DV-8606AU2249.

Areas of Application

The FRIALEN reduced TA red pieces are used for pipe outlets of HD-PE pipelines.

Assembly Instructions

The fusion of the pipe ends with the FRIALEN TA red takes place by FRIALEN-fusing – leakproof and longitudinally strong.

The pipe ends are prepared (removing the oxide layer/cleaning) according to the general installation instructions (see “Assembly Instructions” for “FRIALEN-Safety Fittings for house connections and distribution pipes up to d 225”).

Good reasons for using the FRIALEN TA red:

  • Large coupler depth for ease of pipe guiding (no holding clamps required)
  • At dim. up to d1 63, Length of outlet spigot dimensioned for two fusion operations
  • Extra wide fusion zones
  • Maximum stability through great wall thickness
  • Cold zones at the front side and in the middle of the coupler
  • Exposed heating coil for direct heat transmission to the pipe
  • Small annular gap for build-up of optimum joining pressure in the fusion zone
  • Touch proof electric contacts
  • Durable batch marking
  • Individually wrapped for dirt protection
    Additional barcode for tracing back the fitting (Traceability-Coding)